Stuart-turner Techflo Turbo 15TNH Manual de usuario

Installation, Operation & Maintenance InstructionsPlease leave this instruction booklet with the home owner as it contains important guarantee, ma

- 10 -Cont ...3. Check in the mouth of the fitting that ‘O’-ring, nylon washer and collet are in position.4. Push pipe firmly into fitting, unti

- 11 -Cont ...4 ELECTRICAL INSTALLATION / EARTHING4.11 Regulations: The electrical installation must be carried out in accordance with the cu

- 12 -Cont ...4.23 Supply Cord Replacement:The supply cord and internal wiring within the terminal box are routed and secured to ensure compliance wi

- 13 -Cont ...4.24 Cable Gland Fitting Instructions: To enable correct assembly of the cable gland the ‘O’-ring (Fig. 14 item 1) must be placed

- 14 -Cont ...5 COMMISSIONING5.11 System Flushing: This pump incorporates push-in connectors and plastic components that must not come into con

- 15 -Cont ...5.14 Starting: a) Ensure all outlets are closed, turn power supply ‘on’ - pump will start, pressurise the system then stop. b

- 16 -Cont ...6 MAINTENANCE6.11 Turn off water supplies to the pump and release pressure by opening water outlets before attempting maintenance.

- 17 -Cont ...6.14 Pressure vessel: The pressure vessel air charge does not require routine maintenance. Should ever the need arise for the ves

- 18 -Cont ...7 TECHNICAL SPECIFICATIONTechflow reserve the right to amend the specification in line with its policy of continuous development of its

- 19 -8 TROUBLE SHOOTING GUIDESymptoms Probable Cause Recommended ActionPump will not start. Electrical supply. Check power supply.Check fuse (see fu

- 2 -Cont ...PRODUCT DESCRIPTIONElectric motor driven twin ended peripheral pump, complete with an automatic control system, consisting of flow switch

- 20 -Cont ...8.11 Dry Run Protection: This pump is fitted with a PCB that will detect the following fault conditions:  Dry running caused by wat

- 21 -Cont ... IMPORTANT – Ensure there is no contact with any of the internal parts of the terminal box.  Briefly reconnect the mains power su

- 22 -Cont ...8.14 Flow Switch Circuit Test: 1. First confirm visually that the flow switch reed clamps have not been dislodged during handl

- 23 -Cont ...9 THE TECHFLOW GUARANTEE Congratulations on purchasing a Techflow pump. We are confident this pump will provide many years of troubl

DECLARATION OF CONFORMITY2006/42/ECBS EN ISO 12100-1, BS EN ISO 12100-2, BS EN 8092006/95/ECBS EN 60335-1, BS EN 60335-2-412004/108/ECBS EN 55014-1, B

- 3 -CHECKLISTItemDescription QtyItemDescription QtyPump 1 Hose with isolating valve 2Hose 2Your product may vary slightly from the picture above.PRE-

- 4 -Cont ...1 READ BEFORE COMMENCING PUMP INSTALLATIONA. Water storage capacity.1.11 The hot and cold water storage capacity must be sufficient to

- 5 -Cont ...2 LOCATION - GENERAL2.11 Access: For emergencies and maintenance the pump must be easily accessible.2.12 Protection: The pump must

- 6 -Cont ... The following method will help to overcome the problem: A “U” bend or downward loop in the supply pipe to the pump of 350 mm depth

- 7 -Cont ...Cold water connection:2.27 The cold water supply: The supply must be air free and have a dedicated connection to the tank which sh

- 8 -Cont ...Hot water connection:2. 29 Hot water cylinder or storage tank: When a hot water cylinder or storage tank is used, ensure the pipewor

- 9 -Cont ...3 PUMP CONNECTIONS  Do not use stainless steel, chrome or nickel plated pipe with the flexible hose push-in plumbing connections.